Here is a link to a wonderful glaze spraying booklet produced by an Aussie, Roger Graham. It contains references to Australian companies, measurements are in metric and other such specifics that need translation for those in the U.S. but still gobs of good information, targeted to those who know little about spraying glazes:

 

http://www.luepottery.hwy.com.au/PDF/glaze%20spray.pdf

 

The following is from the intro to the booklet:

 

"The booklet is still copyrighted, but we have no problem if other potters make

printouts for their own use. For those who actually go ahead and try some of

the ideas, we’d be glad to hear of your results. And if you have other

creative glaze-spraying tricks of your own, we’d love to know. Easiest by

email:

rogergraham@optusnet.com.au "

Views: 690

Reply to This

Replies to This Discussion

Thank you for posting the link to  this very informative pdf.  I read the entire thing.  I still have one question.  I just purchased an HVLP Gravity Feed spray gun with pressure guage from Harbor Freight.  I have played with it with water,  have not glazed anything yet.  I need to know what the pressure reading on the guage should ideally be.  Thanks everyone!

Hi Nadine,

     I believe the limit is 65 psi, but I keep mine at about 60 psi.  Is this the purple one from Harbor Freight?

Just make sure you keep it cleaned out when you have finished spraying.  It is fairly simple to take apart & clean if it gets clogged.  Also I keep mine upside down after I clean it to let the water run out, but you can also hook it back up to the compressor to get the water out of it as well.  I have been using the same one for a couple of years now with no problems.  Let me know if you need any help.  jhp

Jeff, 

Thank you for the information and yes,  it is the purple one with the pressure gauge.  I decided to just jump in and spray glaze and I was thrilled with what a good job it did.  I cleaned it completely by filling the container with water and spraying it empty 3 times.  I finally finished glazing and loading and I am now going to my well earned and needed shower!

That's a good idea.  When I am done spraying, I take a wet towel & wipe my face & neck & arms.  It's as much for me as my toy poodle.  He's a licker & if I lay down on the couch(I usually do after spraying) he will proceed to give me a bath and I don't think it would be a good idea for him to lick all those chemicals.

I run 40 psi out of my compressor and don't use the on-gun gauge. I try to balance the fluid control and air mix to spray the largest drops at the least velocity that will give me good, even coverage. This is to reduce the amount of atomization and deflection of glaze particles away from the piece and out of my spray booth. I wear glasses. If I see no glaze droplets on them after a glaze session, and none on my arms, then I feel like I'm doing a good job with my pressure and mixtures.

Thank you for the reply George,  I was running a lot less than that around 30 and I chose the same approach to run the largest drops.  I hope that my results will be good.  Now I have to solve the next problem!  My controller is having a big issue.  I am going to contact Skutt tomorrow to see if they can trouble shoot me through it on the phone.  I am praying that I won't need to send them the controller.  It was very discouraging not to be able to fire after having glazed everything...

Thanks Belinda,

This booklet has a lot of very good information.  I do not have a spray booth/gun yet but I am seriously thinking about moving in that direction.  Your information is very timely for me.

There is another extensive discussion on the subject of spraying glazes at http://cone6pots.ning.com/forum/topics/spraying-glazes (including a link to Graham's tutorial). This comment is just to link the two together to avoid too much redundancy.

Rebecca McMann posed this question to me. I'm passing it on to this topic.

I tried spraying glazes for the first time last night, but my hvlp gun sprayed intermittently, even though I sieved many of the glazes. It's a very sensitive gun and it sprays fine with water. I was wondering if my glaze is too thick for the gun. I tried pulling out the needle a ways to let more glaze out, but then I got such huge coverage, and my pots are small. Any ideas on how to adjust my gun? Do I need to thin my glaze more? Do I need a detail gun? I don't want to spray any more of my pots until I can get a consistent stream. Any help is appreciated! Thanks.

Reply to Discussion

RSS

Videos

  • Add Videos
  • View All

Use These Links to Support Us

Low cost flat lapping disc can be used on you potters wheel if you, drill bat pin holes in it, and provide a trickle of water to cool it. At amazon.com, 120 grit for aggressive material removal. Click the image to purchase 

Members have had great things to say about John Britt's new book, Mid-Range Glazes. Click the image to buy from Amazon.com

Purchase Glazes Cone 6 by Michael Bailey, The Potters Book of Glaze Recipes by Emmanuel Cooper, or Making Marks by Robin Hopper, all available at amazon.comMastering Cone 6 Glazes by John Hesselberth & Ron Roy is now out of print.

Harbor Freight is a great place to find unbeatable prices for better HVLP spray guns with stainless steel parts and serviceable economy models, as well as detail guns, all tested by our members for spraying glazes, as well as compressors to power the guns. As yet no one has tested and commented on the remarkably inexpensive air brushes at harbor freight.

The critter siphon gun is a spray alternative that is well liked by some of our members, and is available at amazon.

Amazon is also a competitive source for photo light tents for shooting professional quality pictures of your work. They also have the EZ Cube brand favored by several of our members. You might also want to purchase the book Photographing Arts, Crafts and Collectibles . . .

If you are up to creating videos of your work or techniques you might want to invest in a flip video camera

Following are a few scales useful for potters. Ohaus Triple Pro Mechanical Triple Beam Balance, 2610g x 0.1g, with Tare $169.00

And finally a low cost clone of the OHaus. The Adam Equipment TBB2610T Triple Beam Mechanical Balance With Tare Beam $99.62

ebay is a great alternative for many tools and the equipment used in the ceramics studio - kilns, wheels, extruders, slab rollers are often listed there both new and used.

Tips for Members

If you just want to spout off, it is best accomplished as a blog posting. If you want to get more guidance and ideas from other members, ask a question as a new discussion topic. In the upper right corner of the lists for both types of posting, you will find an "+Add " button. Clicking it will open an editor where you create your posting. 4/16/2014

© 2024   Created by Andrea Wolf.   Powered by

Badges  |  Report an Issue  |  Terms of Service