It appears most of the folks on this forum are spraying Steven's glazes as he recommends. Has anyone dipped the glazes instead? If so, how are the result? Any suggestions? What to avoid? Etc?

 

Oh, for a spray booth..........sigh.

 

Belinda

Views: 1078

Replies to This Discussion

Before we had a spray booth, we made do with a large cardboard box, such as you might get a washer or dryer in. Use it outside, set it on a folding table, use clamps as necessary, put a turntable or banding wheel in the center, drape a sheet of very lightweight plastic over the front to protect yourself and lift the plastic over your hands while spraying. Doesn't cost more than a few $$ for the plastic, the rest is free or in your studio already. 

I tried dipping the rims of my pots with the Hanna's blue ash and it was way too heavy an application. I dont know if you could adjust the glazes for dipping though. I'm with Robert Shaw though on using a box.

I've dipped the rims on a few of my soup/cereal bowls and I like the effect quite well. In my photos look for this image: Cognac Gold Soup:Cereal Bowl-3. Look also at  Cognac Gold Soup:Cereal Bowl-7 thru 9.

I dip the SCM quick and dipped the whole bowl in Randy's Red to a four count.. I fire a cone 04 bisque, just to give you an idea.

I am dipping all of the glazes now because I don't have a spray booth either.  The SCM works the same as when sprayed.  The only glaze that won't work is the spotted black.  Otherwise, I have been getting great results with SCM and the watercolors using Steven's firing schedule.  I have tested SCM under all of my dipping glazes.  Just go for it!

I am currently using a large cardboard box as a spray booth. I tape large sheets of newspaper to completely line the inside of the box. I put the box on a card table and put pots on a turn table. I spray outside and wear a mask and goggles ( I worry about the overspray getting in my eyes, cant be good). Then when finished spraying, I remove all the paper and renew it for next time. Works very well.

Whoa, Robert! Those Cognac Gold pieces are stunning! You've certainly taken your glaze combos to a gorgeous new level. It was fun to look at your entire photo album and see the the progression of pots as you've moved to more bold colors. Thank you for sharing so much information.

Belinda

Thanks for the input, Michele. I'm ready to mix up dip-able quanities of Steven's glazes after reading your post. It appears everyone dips/sprays SCM as the first layer with another glaze on top of it. Do you dip it as a thin application or do you treat it like a regular glaze? On a vertical surface, does it make the second glaze run much? I'm so hesitant to put an unknown glaze on anything but the top 1/4 of a pot until I know how it behaves. 

Oh, this is exciting!!  Thank you.

GREAT idea to line your spray box with newspaper! An instant grab of excess glaze.  Have you ever thought to tear shapes out of the glaze covered newspaper and lay 'em on a pot to see how it would look after being fired? If the glaze is thick enough, that might turn out really fantastic. If I decide to spray glazes, I'll let you know how it works.

I had a friend who had developed a lovely palette of glazes. She saved all her "trash" glaze into one bucket, never mixed it until glaze time and then only enough to be able to dip. Those were some of her most beautiful pots and they could never be repeated. 

That is why I'm hesitant to dip Steven's glazes. They interact so beautifully but I don't know what to expect and I'm terrified of ruining my kiln shelves. Thank you for the warning.

Just be sure the SCM is a very thin layer. It will cause other glazes to run like crystalline glazes tend to do. Joe usually does a very fast dip (when he dips) of the SCM, and then puts the other glazes on the top 1/3 to 1/2 of the bowls. We use glaze catchers under the bowls, made of the same clay. The center of the glaze catcher needs to be higher than the outer rim, at least for our bowls, that way the glaze runs off in the channel, but the sides of the bowls/pots/whatever do not touch the outer rims of the glaze catcher. Joe has been redesigning the foot of his pieces and does not make a foot rim, per se. The bowls seem to be floating rather than showing a foot beneath. He also tries to put about three small inscised lines at the bottom outer rim of the bowls to help slow down any runs of glaze. If you would like some photos, we can post some if you need it to be more clear. So, to make a long post short, very quick then layer of SCM, other glazes on top third to half of the piece in order to have plenty of room for the glazes that like to run, glaze catcher below and three inscised lines. Lots of little steps, but a good outcome for the work you put in. You can see how close the glaze came to running on the lager glass.

Attachments:

Thanks again, Robert. Do you guys put glaze catchers under all your pots? Yikes!  If so, that means you also grind alot of your pots.  I have a grinder with a wheel that will eat glaze drips in half a second but I don't have anything to smooth the rough surface with. Can you tell me what you use to fine grind and where I might get it?

I know this isn't exactly Steven Hill's recipes, but it's the same theory.  Here's a combination I really like dipped.  It is Tom Coleman's Crystal Matte underneath Ron Roy's black number 3.  It makes a really nice effect and doesn't run off the pot.

Attachments:

RSS

Videos

  • Add Videos
  • View All

Use These Links to Support Us

Low cost flat lapping disc can be used on you potters wheel if you, drill bat pin holes in it, and provide a trickle of water to cool it. At amazon.com, 120 grit for aggressive material removal. Click the image to purchase 

Members have had great things to say about John Britt's new book, Mid-Range Glazes. Click the image to buy from Amazon.com

Purchase Glazes Cone 6 by Michael Bailey, The Potters Book of Glaze Recipes by Emmanuel Cooper, or Making Marks by Robin Hopper, all available at amazon.comMastering Cone 6 Glazes by John Hesselberth & Ron Roy is now out of print.

Harbor Freight is a great place to find unbeatable prices for better HVLP spray guns with stainless steel parts and serviceable economy models, as well as detail guns, all tested by our members for spraying glazes, as well as compressors to power the guns. As yet no one has tested and commented on the remarkably inexpensive air brushes at harbor freight.

The critter siphon gun is a spray alternative that is well liked by some of our members, and is available at amazon.

Amazon is also a competitive source for photo light tents for shooting professional quality pictures of your work. They also have the EZ Cube brand favored by several of our members. You might also want to purchase the book Photographing Arts, Crafts and Collectibles . . .

If you are up to creating videos of your work or techniques you might want to invest in a flip video camera

Following are a few scales useful for potters. Ohaus Triple Pro Mechanical Triple Beam Balance, 2610g x 0.1g, with Tare $169.00

And finally a low cost clone of the OHaus. The Adam Equipment TBB2610T Triple Beam Mechanical Balance With Tare Beam $99.62

ebay is a great alternative for many tools and the equipment used in the ceramics studio - kilns, wheels, extruders, slab rollers are often listed there both new and used.

Tips for Members

If you just want to spout off, it is best accomplished as a blog posting. If you want to get more guidance and ideas from other members, ask a question as a new discussion topic. In the upper right corner of the lists for both types of posting, you will find an "+Add " button. Clicking it will open an editor where you create your posting. 4/16/2014

© 2024   Created by Andrea Wolf.   Powered by

Badges  |  Report an Issue  |  Terms of Service