Finally got my kiln loaded ready for a bisque firing last night but then discovered that my vent motor had quit..  I probably have to buy a new one but don't want to spend the money to replace the whole venting system (L&L) since it is only the motor that has died.  I am running the bisque firing without a vent system (just took out the top plug) but would prefer to have venting in place for the next firing - cone 6 glaze firing.  Any advice from you more experienced types out there?

Views: 183

Reply to This

Replies to This Discussion

Hi Joan, 

   I found the same exact motor they use for the Sure Vent System on-line at Amazon. Dayton Motors The cost is $65 with free shipping.  This is a bare motor so I had to add the 3" and 4" vent hookups and a pigtail.  The vent collars were a bit tricky as I was not replacing a motor that had them on, (I was adding a 3rd kiln and didn't want to spend $200+ for just the motor.)  You should be able to jury rig your old 3" and 4" hookups to the new motor.  I went to Lowes and made some of the connectors work using tin snips and a collar ring I found there .  You can get one of the hookups sold separately, if you look at The Ceramic Shop website theceramicshop.com, they have one listed.

Also a bit of a hint to keep the motor running longer...  A friend who builds and rebuilds large specialized industrial motors told me that these motors don't come with the oil holes that they used to have.  He had me drill a hole in the middle of the plate directly across from the 3" hookup. Just big enough to put one or two drops of oil from a 3in1 bottle. I did it to my 4 year old motor that was whining pretty bad, which he said were the ball barrings needing oil.  Took three drops and no more noise or vibration since. I put  one drop of oil in about every 20th firing.  Be careful do not use more than a drop or two.  (I only have ever used a drop.)

Hope this helps.

Catherine

Thank you Catherine, that is great info to have.  By vacuuming and just general fiddling I managed to get the old motor going again but I think the prudent thing to do is to order a replacement motor now when its not an emergency.  That's a great price, particularly when one thinks of the cost of replacing the whole system.

Thanks again,

Joan

Your welcome Joan...  

Another vent tip:  Keep a cheap inline fan for bathrooms tucked away, found at Lowes.  If your motor quits and your in a pinch you can use it to push more than enough air to get you by.  I saw a few blog posts of potters using them as their main fan.  I would think that they would not have a long life, but they would work in a pinch.

Happy Potting,

Catherine

Thanks for another good tip Catherine.  I do think in my case just going for the Dayton Blower from Amazon is the way to go.  My old blower, tho functioning now, is pretty old and sure to quit soon and at $67 it would be worthwhile to have the Dayton as a back up, all ready to hook up.

Happy Potting to you too (it is a happy activity, keeps me sane-ish)

Joan

Those motors will freeze up eventually, but you can often get them going again with a good cleaning. Lots of WD40 will usually loosen it up and get it going again. They can often run for a couple more years after cleaning.

Reply to Discussion

RSS

Videos

  • Add Videos
  • View All

Use These Links to Support Us

Low cost flat lapping disc can be used on you potters wheel if you, drill bat pin holes in it, and provide a trickle of water to cool it. At amazon.com, 120 grit for aggressive material removal. Click the image to purchase 

Members have had great things to say about John Britt's new book, Mid-Range Glazes. Click the image to buy from Amazon.com

Purchase Glazes Cone 6 by Michael Bailey, The Potters Book of Glaze Recipes by Emmanuel Cooper, or Making Marks by Robin Hopper, all available at amazon.comMastering Cone 6 Glazes by John Hesselberth & Ron Roy is now out of print.

Harbor Freight is a great place to find unbeatable prices for better HVLP spray guns with stainless steel parts and serviceable economy models, as well as detail guns, all tested by our members for spraying glazes, as well as compressors to power the guns. As yet no one has tested and commented on the remarkably inexpensive air brushes at harbor freight.

The critter siphon gun is a spray alternative that is well liked by some of our members, and is available at amazon.

Amazon is also a competitive source for photo light tents for shooting professional quality pictures of your work. They also have the EZ Cube brand favored by several of our members. You might also want to purchase the book Photographing Arts, Crafts and Collectibles . . .

If you are up to creating videos of your work or techniques you might want to invest in a flip video camera

Following are a few scales useful for potters. Your final price could be less or more - things change.

American Weigh Black Blade Digital Scale, 1000g X 0.1g $11.08 

For the non-digitally inclined the old standard Ohaus Triple Pro Mechanical Triple Beam Balance, 2610g x 0.1g, with Tare $169.00

And finally a low cost clone of the OHaus. The Adam Equipment TBB2610T Triple Beam Mechanical Balance With Tare Beam $99.62

ebay is a great alternative for many tools and the equipment used in the ceramics studio - kilns, wheels, extruders, slab rollers are often listed there both new and used.

Tips for Members

If you just want to spout off, it is best accomplished as a blog posting. If you want to get more guidance and ideas from other members, ask a question as a new discussion topic. In the upper right corner of the lists for both types of posting, you will find an "+Add " button. Clicking it will open an editor where you create your posting. 4/16/2014

© 2021   Created by George Lewter.   Powered by

Badges  |  Report an Issue  |  Terms of Service