Skutt kiln not reaching temperature - Electric Mid&Hi Fired Ceramics2024-03-29T15:41:29Zhttps://cone6pots.ning.com/forum/topics/skutt-kiln-not-reaching-temperature?commentId=2103784%3AComment%3A124023&feed=yes&xn_auth=noM. I removed the blank ring a…tag:cone6pots.ning.com,2015-08-23:2103784:Comment:1246582015-08-23T18:31:08.465ZRobert spicerhttps://cone6pots.ning.com/profile/Robertspicer
M. <br></br>I removed the blank ring and fired the kiln and it did I fact reach cone six and shut off
<br></br>
<cite>Norm Stuart said:</cite><blockquote cite="http://cone6pots.ning.com/forum/topics/skutt-kiln-not-reaching-temperature#2103784Comment124023"><div><div class="xg_user_generated"><p>I'd be surprised if the addition of a blank ring causes a kiln to lose that much ability to reach temperature.</p>
<p>Using only 20 amps I suppose it's possible, even though it's called a Cone 6 Kiln rated at…</p>
</div>
</div>
</blockquote>
M. <br/>I removed the blank ring and fired the kiln and it did I fact reach cone six and shut off
<br/>
<cite>Norm Stuart said:</cite><blockquote cite="http://cone6pots.ning.com/forum/topics/skutt-kiln-not-reaching-temperature#2103784Comment124023"><div><div class="xg_user_generated"><p>I'd be surprised if the addition of a blank ring causes a kiln to lose that much ability to reach temperature.</p>
<p>Using only 20 amps I suppose it's possible, even though it's called a Cone 6 Kiln rated at 2250 F.</p>
<p></p>
<p>Our 36 amp Cress E-23 fails to reach temperature only after a second or third element has failed, depending on the element. Which means the kiln has been firing unevenly for a while.</p>
<p></p>
<p>So we periodically do our dead-simple "paper test". Stick a small strip of paper next to each coil and after firing for 5 minutes or so, and see which coils are not hot enough to burn paper. If there's more than one coil out, it may be a relay. It sure beats playing around with electric test meters.</p>
<p><img alt="http://www.publicsurplus.com/sms/docviewer/aucdoc/Kiln5.jpg?auc=665401&docid=4453053" src="http://www.publicsurplus.com/sms/docviewer/aucdoc/Kiln5.jpg?auc=665401&docid=4453053"/></p>
<p></p>
<p></p>
</div>
</div>
</blockquote> New equipment, always a good…tag:cone6pots.ning.com,2015-08-12:2103784:Comment:1243452015-08-12T07:16:29.464ZNorm Stuarthttps://cone6pots.ning.com/profile/NormStuart
<p>New equipment, always a good solution.</p>
<p></p>
<p>Cone 8 down to a Cone 1. That's a lot more difference than I would have expected. Good to know.</p>
<p>New equipment, always a good solution.</p>
<p></p>
<p>Cone 8 down to a Cone 1. That's a lot more difference than I would have expected. Good to know.</p> I looked at a skutt 1227 toda…tag:cone6pots.ning.com,2015-08-12:2103784:Comment:1242472015-08-12T01:38:10.085ZRobert spicerhttps://cone6pots.ning.com/profile/Robertspicer
I looked at a skutt 1227 today that is a cone 8 kiln and it states with the blank ring installed it will only fire to cone 1. I believe that may be the problem. Bit I'm buying the 1227 tomorrow and that will fix everything hopefully, thank you for your help
I looked at a skutt 1227 today that is a cone 8 kiln and it states with the blank ring installed it will only fire to cone 1. I believe that may be the problem. Bit I'm buying the 1227 tomorrow and that will fix everything hopefully, thank you for your help One thing I have done in the…tag:cone6pots.ning.com,2015-08-10:2103784:Comment:1241132015-08-10T19:48:37.144ZJeff Poulterhttps://cone6pots.ning.com/profile/JeffPoulter
<p>One thing I have done in the past is add an additional top & bottom to the kiln. I've bought quite a few old kilns and you can set an extra bottom under the kiln(although there's not as much heat loss through the bottom) and set an extra lid on top. that will curb a lot of heat loss through the top but is an extra step when loading & unloading. Like Norm says, a fiber blank works well also, wrapped around the perimeter and/or on top. I have even closed the peeps in the winter time…</p>
<p>One thing I have done in the past is add an additional top & bottom to the kiln. I've bought quite a few old kilns and you can set an extra bottom under the kiln(although there's not as much heat loss through the bottom) and set an extra lid on top. that will curb a lot of heat loss through the top but is an extra step when loading & unloading. Like Norm says, a fiber blank works well also, wrapped around the perimeter and/or on top. I have even closed the peeps in the winter time especially if the wind is blowing and the kiln is struggling, although that does effect some glazes when you keep the kiln closed up like that. When I'm doing moly crystals, I have to have the kiln sealed up as tight as possible anyways. jhp </p> The difference between Cone 1…tag:cone6pots.ning.com,2015-08-10:2103784:Comment:1241122015-08-10T18:19:09.309ZNorm Stuarthttps://cone6pots.ning.com/profile/NormStuart
<p>The difference between Cone 1 and Cone 6 is only 153 F (85 C) 2,232 F vs 2,079 F.</p>
<p></p>
<p>I'm sure Jeff Poulter would agree you need a fairly modest change to:</p>
<p></p>
<p>A.) how much mass and volume you're heating;</p>
<p>B.) how much heat you're losing over the total exposed surface area;</p>
<p>C.) how much heat is being generated by older coils.</p>
<p></p>
<p>You could always ask the people at Skutt who designed the kiln if it can support Cone 6 with a blank ring added,…</p>
<p>The difference between Cone 1 and Cone 6 is only 153 F (85 C) 2,232 F vs 2,079 F.</p>
<p></p>
<p>I'm sure Jeff Poulter would agree you need a fairly modest change to:</p>
<p></p>
<p>A.) how much mass and volume you're heating;</p>
<p>B.) how much heat you're losing over the total exposed surface area;</p>
<p>C.) how much heat is being generated by older coils.</p>
<p></p>
<p>You could always ask the people at Skutt who designed the kiln if it can support Cone 6 with a blank ring added, and ask them how much a cerablanket on the lid would assist their kiln.</p>
<p>503-774-6000</p>
<p><a rel="nofollow" href="http://skutt.com/support-home/contact-support/" target="_blank">http://skutt.com/support-home/contact-support/</a></p>
<p></p>
<p>xxxxxxxxxxxxxxxxxxxxxxxxx</p>
<p>If our Cress kiln were not outdoors, I'd add a 2 inch thick cerablanket onto the lid of our kiln to reduce firing costs, especially as we add a six hour slow-cool onto each firing. Instead I've added a stainless steel cap to protect it from the rain.</p>
<p>It does have a 3/8" air-gap provided by some thin aluminum tubing between the kiln lid and the stainless cap.</p>
<p></p>
<p>When we replace our heating elements, the new elements are visibly 50% thicker or so than the used elements.</p>
<p><a target="_self" href="http://storage.ning.com/topology/rest/1.0/file/get/1605081749?profile=original"><img width="721" class="align-left" src="http://storage.ning.com/topology/rest/1.0/file/get/1605081749?profile=RESIZE_1024x1024" width="721"/></a></p>
<p></p> Do you think taking the blank…tag:cone6pots.ning.com,2015-08-10:2103784:Comment:1242442015-08-10T17:56:01.757ZRobert spicerhttps://cone6pots.ning.com/profile/Robertspicer
Do you think taking the blank ring out will allow the kiln to fire to cone 6 when it will only go to cone 1 now
Do you think taking the blank ring out will allow the kiln to fire to cone 6 when it will only go to cone 1 now A blank ring will definitely…tag:cone6pots.ning.com,2015-08-10:2103784:Comment:1240362015-08-10T01:43:05.858ZJeff Poulterhttps://cone6pots.ning.com/profile/JeffPoulter
<p>A blank ring will definitely bring down the efficiency of your kiln. Taking it out will allow your kiln to be more efficient and reach a higher temperature. I would check the resistance of the old elements compared to the new ones you put in. As elements age, it goes up & they do not generate as much heat and will need to be replaced. Elements that are struggling to output heat make the other ones work harder which means they will fail earlier. If each element adds its fair share,…</p>
<p>A blank ring will definitely bring down the efficiency of your kiln. Taking it out will allow your kiln to be more efficient and reach a higher temperature. I would check the resistance of the old elements compared to the new ones you put in. As elements age, it goes up & they do not generate as much heat and will need to be replaced. Elements that are struggling to output heat make the other ones work harder which means they will fail earlier. If each element adds its fair share, they will all age gracefully. jhp</p> If the old elements look visi…tag:cone6pots.ning.com,2015-08-08:2103784:Comment:1242342015-08-08T04:10:23.409ZNorm Stuarthttps://cone6pots.ning.com/profile/NormStuart
<p>If the old elements look visibly thinner than the replacement elements, then they would probably read differently on a meter, so replacing them would give you more heat. </p>
<p></p>
<p>I'm sure you have no more than one peephole open - we once had someone at our studio who was convinced all of our kiln peepholes all had to be open for an oxidation firing, needless to say not even our kiln which generates a tremendous amount of heat for its size never got anywhere near hot enough with all…</p>
<p>If the old elements look visibly thinner than the replacement elements, then they would probably read differently on a meter, so replacing them would give you more heat. </p>
<p></p>
<p>I'm sure you have no more than one peephole open - we once had someone at our studio who was convinced all of our kiln peepholes all had to be open for an oxidation firing, needless to say not even our kiln which generates a tremendous amount of heat for its size never got anywhere near hot enough with all the peepholes open - in fact you can close all of them if needed as firebrick is fairly porous.</p>
<p></p>
<p>I've heard complaints from people who've bought new inexpensive Paragon kilns rated for Cone 6, that they don't maintain their ability to reach Cone 6 for long. Our kiln is rated for Cone 10 which we fire to Cone 6.</p>
<p></p>
<p>You can always wrap the exterior of your kiln in fiber blanket, after which it should reach temperature, unless you have a thermocouple which is not reading the correct temperature - but I assume you're using cones. As heat rises, most of your heat loss is through the lid, so you could first try Cerablanket on the lid.</p>
<p></p>
<p>Just don't cover the control box with blanket as the mechanical or electrical parts are designed to be air cooled.</p>
<p></p>
<p>The Cerablanket is rated for 2,400 F (cone 10), with a 2,150 F limit for 24/7 industrial usage - the others rated for lower temperatures.</p>
<p><a rel="nofollow" href="http://www.amazon.com/s/ref=nb_sb_noss?url=search-alias%3Daps&field-keywords=cerablanket&rh=i%3Aaps%2Ck%3Acerablanket" target="_blank">Various thickness available on Amazon.com</a></p>
<p><a rel="nofollow" href="http://www.bigceramicstore.com/tools-supplies/firing-supplies/fiber-blanket.html" target="_blank">http://www.bigceramicstore.com/tools-supplies/firing-supplies/fiber...</a></p>
<p></p>
<p>We were once offered a Cone 10 Cress kiln built in the 1950s and I was very surprised to see it operated on 110 volt.</p>
<p>The interior dimensions were square and roughly the size of our kiln - but the exterior of the kiln was as large as a van. It would have required a hefty forklift to move. The kiln lid was roughly 12 inches thick with a heavy counterweight attached to a cable like a weight machine in a gym, and the soft firebrick was surrounded by 4 inches of vermiculite followed by thick layers of fire blanket inside a heavy metal exterior frame. It was built like a tank and we were told it took several days to fire and cool down.</p>
<p></p>
<p>So adding extra insulation does work, allowing lower heat output to overcome parasitic heat loss to the environment and still reach the cone 6 or cone 10 limit of the heating elements you're using.</p>
<p></p>
<p>If you look back at posts from last week Maulik Oza has photos of a gas raku kiln they built with a steel frames covered by cerablanket, which is the same concept as this Russian built gas kiln.There's no rule which requires us to use firebrick, or firebrick alone.</p>
<p><a rel="nofollow" href="http://pottery.su/tag/Cerablanket/" target="_blank">http://pottery.su/tag/Cerablanket/</a></p>
<p><a rel="nofollow" href="https://translate.google.com/translate?sl=ru&tl=en&js=y&prev=_t&hl=en&ie=UTF-8&u=http%3A%2F%2Fpottery.su%2Ftag%2FCerablanket%2F&edit-text=" target="_blank">English Translation for Russian Kiln</a></p>
<p><img alt="http://pottery.su/uploads/images/00/00/01/2014/04/22/483d11.jpg" src="http://pottery.su/uploads/images/00/00/01/2014/04/22/483d11.jpg"/></p>
<p></p> I did the paper test and the…tag:cone6pots.ning.com,2015-08-08:2103784:Comment:1242312015-08-08T02:29:37.627ZRobert spicerhttps://cone6pots.ning.com/profile/Robertspicer
I did the paper test and the top two elements didn't seem to be heating up properly so I changed them. I'm at a loss. The bottom elements are working but I don't know of a way to tell if they're working properly or not. I guess I could change the bottom elements also
I did the paper test and the top two elements didn't seem to be heating up properly so I changed them. I'm at a loss. The bottom elements are working but I don't know of a way to tell if they're working properly or not. I guess I could change the bottom elements also I'd be surprised if the addit…tag:cone6pots.ning.com,2015-08-08:2103784:Comment:1240232015-08-08T01:16:02.082ZNorm Stuarthttps://cone6pots.ning.com/profile/NormStuart
<p>I'd be surprised if the addition of a blank ring causes a kiln to lose that much ability to reach temperature.</p>
<p>Using only 20 amps I suppose it's possible, even though it's called a Cone 6 Kiln rated at 2250 F.</p>
<p></p>
<p>Our 36 amp Cress E-23 fails to reach temperature only after a second or third element has failed, depending on the element. Which means the kiln has been firing unevenly for a while.</p>
<p></p>
<p>So we periodically do our dead-simple "paper test". Stick a small…</p>
<p>I'd be surprised if the addition of a blank ring causes a kiln to lose that much ability to reach temperature.</p>
<p>Using only 20 amps I suppose it's possible, even though it's called a Cone 6 Kiln rated at 2250 F.</p>
<p></p>
<p>Our 36 amp Cress E-23 fails to reach temperature only after a second or third element has failed, depending on the element. Which means the kiln has been firing unevenly for a while.</p>
<p></p>
<p>So we periodically do our dead-simple "paper test". Stick a small strip of paper next to each coil and after firing for 5 minutes or so, and see which coils are not hot enough to burn paper. If there's more than one coil out, it may be a relay. It sure beats playing around with electric test meters.</p>
<p><img alt="http://www.publicsurplus.com/sms/docviewer/aucdoc/Kiln5.jpg?auc=665401&docid=4453053" src="http://www.publicsurplus.com/sms/docviewer/aucdoc/Kiln5.jpg?auc=665401&docid=4453053"/></p>
<p></p>
<p></p>