The simple Magnetic Trimming Chuck can be a weekend project if you have a few hand tools and some experience cutting sheet metal.  The 11.5" diameter steel disc is cut from galvanized sheet stock bought at Home Depot for $4.  Although I didn't try it, you could probably get the same result without cutting metal by using the bottom of a 11" two-part steel (not aluminum) quiche baking dish bought from a kitchen shop, or on Amazon.

The steel disc is glued to any 12" bat that already fits your wheel.  I stuck mine together with strong double-sided sticky tape.  Four 1/4" Neodymium magnets are  epoxied to three 1.5" square pine blocks.  Dimensions are not critical, but it is a bit of a trick to keep the magnets from jumping together during assembly.  The blocks were faced with scrap foam Gripper Pad, but any medium stiff foam can be used.

So far the magnet trimming holder works well and is somewhat easier than using clay wads.  I have yet to make up a set of extension dowel rods for holding tall pieces.  Good luck and let us know how it goes, and if you have improvements.

11" Steel Quiche Pan:

http://www.amazon.com/Kaiser-Bakeware-Tinplate-11-Inch-Removable/dp...

Magnets:

http://www.amazon.com/Neodymium-Magnets-inch-Disc-N48/dp/B001KUWM3C...

Gripper Pads:

http://www.amazon.com/gp/product/B002LHVNTM/sr=1-65/qid=1361548645/...

Edit:#1 To Magnet Trimming Chuck

Hardest part of project is epoxying magnets because they want to spring together and make a mess.  So I've made a magnet assembly jig.

The photos show how to use the jig to make the three magnetic blocks.  First hammer then sand the tack heads flush then follow the photos. When chuck is finished first center your pot then slide the blocks to hold the pot. Any number of blocks can be used for any shape pot. 

John255

Edit #2

My attempts to build simple extensions for trimming tall pots were complicated.

Another approach I use successfully is to throw a double-ended trimming chuck and bisque  fire it. Then center the chuck on the mag-trim. (See photo below)  Dimensions are not critical.  I use a bulls-eye level to level the pot in the chuck. (This assumes your wheel is level.)  You could also buy a set of extensions from Bailey for about $16 and screw then to the mag-trim blocks if you like.

http://www.baileypottery.com/potterywheels/quicktrim2.htm

Good luck with your Mag-trim, and let us know how it goes.

John255

Views: 3469

Reply to This

Replies to This Discussion

Brian,

Thank you for responding.

I was beginning to wonder if anyone was reading this.

Seeing some interest will help me to get busy making the extensions for tall pieces.

Total cost should be about 1/10 the price of Giffen Grip.

Regards,

John255

Very cool idea! 

Thanks for sharing it.

OK Doug.

Glad you liked the post.

John255

Brian,

Your observation is true that you can add as many magnetic blocks as needed in any position.  If you wanted to add a thrown foot to a square slab pot that would be no problem.  All you would do is first center the piece and then add the holding blocks.

Thanks for your informative post.

John255

Perhaps I am the only person here who does not understand how this tool works to keep the pot on the bat....Please clarify.

Thank you!

Nadine

If you are following this thread please note that I've modified the original post with EDIT#2 that includes an extension trimming chuck for trimming long-neck and domed pieces. 

Thanks,

John255

Reply to Discussion

RSS

Videos

  • Add Videos
  • View All

Use These Links to Support Us

Low cost flat lapping disc can be used on you potters wheel if you, drill bat pin holes in it, and provide a trickle of water to cool it. At amazon.com, 120 grit for aggressive material removal. Click the image to purchase 

Members have had great things to say about John Britt's new book, Mid-Range Glazes. Click the image to buy from Amazon.com

Purchase Glazes Cone 6 by Michael Bailey, The Potters Book of Glaze Recipes by Emmanuel Cooper, or Making Marks by Robin Hopper, all available at amazon.comMastering Cone 6 Glazes by John Hesselberth & Ron Roy is now out of print.

Harbor Freight is a great place to find unbeatable prices for better HVLP spray guns with stainless steel parts and serviceable economy models, as well as detail guns, all tested by our members for spraying glazes, as well as compressors to power the guns. As yet no one has tested and commented on the remarkably inexpensive air brushes at harbor freight.

The critter siphon gun is a spray alternative that is well liked by some of our members, and is available at amazon.

Amazon is also a competitive source for photo light tents for shooting professional quality pictures of your work. They also have the EZ Cube brand favored by several of our members. You might also want to purchase the book Photographing Arts, Crafts and Collectibles . . .

If you are up to creating videos of your work or techniques you might want to invest in a flip video camera

Following are a few scales useful for potters. Ohaus Triple Pro Mechanical Triple Beam Balance, 2610g x 0.1g, with Tare $169.00

And finally a low cost clone of the OHaus. The Adam Equipment TBB2610T Triple Beam Mechanical Balance With Tare Beam $99.62

ebay is a great alternative for many tools and the equipment used in the ceramics studio - kilns, wheels, extruders, slab rollers are often listed there both new and used.

Tips for Members

If you just want to spout off, it is best accomplished as a blog posting. If you want to get more guidance and ideas from other members, ask a question as a new discussion topic. In the upper right corner of the lists for both types of posting, you will find an "+Add " button. Clicking it will open an editor where you create your posting. 4/16/2014

© 2024   Created by Andrea Wolf.   Powered by

Badges  |  Report an Issue  |  Terms of Service